Instalaciçon

Si tienes problemas al aplicar nuestros adhesivos, aquí tienes algunos tutoriales para aprender a hacerlo

Elije un producto: Honda Africa Twin CRF 1100,  BMW R 1200 GS/GSA LC swingarm sticker, BMW R 1200 GS, BMW S1000XR decal, BMW S1000XR TankPad, Car Rear Bumper protector, Rim Sticker, Yamaha MT09 Tracer, Yamaha Ténéré 700, Yamaha TMAX 530

HONDA AFRICA TWIN CRF 1100

BMW R 1200 GS/GSA LC swingarm sticker

 

Recuerda aplicar el adhesivo en un lugar con buena temperatura (entre 25ºC y -15ºC).
Te recomendamos no usar la moto hasta que hayan pasado 48 horas desde la instalación de los adhesivos, para que el pegamento actúe con su máxima capacidad.

La instalación consiste en:

1. Comienza limpiando la superficie donde vas a aplicar el adhesivo únicamente con alcohol. Evita limpiadores industriales que puedan dañar la pintura de la moto o el pegamento del adhesivo.

2. Preajusta el adhesivo sin pegarlo para asegurarte de que lo instalas de la manera correcta.

3. Retira el respaldo adhesivo por un extremo.

4. Aplica la parte sin papel de silicona. Ahora sigue aplicando el resto de la pieza mientras retiras el resto del papel de silicona. Recuerda hacerlo en la misma dirección para que no se quede aire atrapado bajo el adhesivo, lo que podría causar burbujas.

 

BMW R 1200 GS

 

 

BMW S 1000 XR Graphics

 

 

BMW S 1000 XR Tank Pad

 

Car Rear Bumper Protector

This product has the the front flap of the packaging designed to be used as a sustainable squeegee.

Remember to apply the sticker in a good tempered place (between 25ºC and -15ºC).

We recommend not to put anything onto the sticker until 48h-72h have past from the stickers installation, so the glue acts at its full capacity. 

The installation consists in:

1. Start cleaning the surface where you are going to apply the sticker with only alcohol. Avoid industrial cleaners that can damage the motorcycle paint or the glue in the sticker.

2. Remove the central part of the adhesive backing and stick it at the center of the bumper.

3. Start sticking one side while removing the backing and appliying pressure with the squeegee to remove the air.

4. Do the same on the other side of the sticker.

 

Rim Sticker

Remember to apply the sticker in a good tempered place (between 25ºC and -15ºC).
We recommend not to use the motorcycle until 48h have past from the stickers installation, so the glue acts at its full capacity.

The installation consists in:

1. Start cleaning the surface where you are going to apply the sticker with only alcohol. Avoid industrial cleaners that can damage the motorcycle paint or the glue in the sticker.

2. Choose which part of the rim you want to decorate first. Preset the sticker without hooking it to make sure you install it the correct way.

3. Peel off the adhesive backing.

4. Apply the piece in the same direction so no air gets stuck under the sticker making bubbles.

 

Yamaha MT09 Tracer

Remember to apply the sticker in a good tempered place (between 25ºC and -15ºC).
We recommend not to use the motorcycle until 48h have past from the stickers installation, so the glue acts at its full capacity.

The installation consists in:

1. Start cleaning the surface where you are going to apply the sticker with only alcohol. Avoid industrial cleaners that can damage the motorcycle paint or the glue in the sticker.

2. Peel off the adhesive backing on one end.

3. Preset the sticker without hooking it to make sure you install it the correct way.

4. Apply the part with no silicon paper. Now keep applying the rest of the piece while removing the rest of the silicon paper. Remember to do it in the same direction so no air gets stuck under the sticker making bubbles.

 

Yamaha Ténéré 700

 

Remember to apply the sticker in a good tempered place (between 25ºC and -15ºC).
We recommend not to use the motorcycle until 48h have past from the stickers installation, so the glue acts at its full capacity.

The installation consists in:

1. Start cleaning the surface where you are going to apply the sticker with only alcohol. Avoid industrial cleaners that can damage the motorcycle paint or the glue in the sticker.

2. Peel off the adhesive backing on one end.

3. Preset the sticker without hooking it to make sure you install it the correct way.

4. Apply the part with no silicon paper. Now keep applying the rest of the piece while removing the rest of the silicon paper. Remember to do it in the same direction so no air gets stuck under the sticker making bubbles.

 

Yamaha TMAX 530

Remember to apply the sticker in a good tempered place (between 25ºC and -15ºC).
We recommend not to use the motorcycle until 48h have past from the stickers installation, so the glue acts at its full capacity.

The installation consists in:

1. Start cleaning the surface where you are going to apply the sticker with only alcohol. Avoid industrial cleaners that can damage the motorcycle paint or the glue in the sticker.

2. Peel off the adhesive backing on one end.

3. Preset the sticker without hooking it to make sure you install it the correct way.

4. Apply the part with no silicon paper. Now keep applying the rest of the piece while removing the rest of the silicon paper. Remember to do it in the same direction so no air gets stuck under the sticker making bubbles.